mirror of
https://github.com/freebsd/freebsd-src.git
synced 2024-12-05 16:39:31 +00:00
66 lines
2.3 KiB
Plaintext
66 lines
2.3 KiB
Plaintext
|
$Id: README.de,v 1.1 1994/08/16 20:40:56 thomas Exp $
|
||
|
|
||
|
----------------
|
||
|
|
||
|
The enclosed driver should be considered as beta-test software. It
|
||
|
has run on exactly one machine. Therefore testing has been limited.
|
||
|
This driver is in no way supported by Digital Equipment. See the
|
||
|
disclaimers in the sources for more.
|
||
|
|
||
|
This driver the DEC DE435 PCI NIC. It should also work with other PCI
|
||
|
boards that use the DC21040-AA chip (also known as TULIP). This
|
||
|
driver requires the DC21040-AA to be pass 2.3 or later. If you are
|
||
|
using a eariler pass chip, you may encounter undetected transmit
|
||
|
corruptions. This driver also requires that DC21040-AA use a serial
|
||
|
Ethernet address ROM as described in the DC21040 specification.
|
||
|
|
||
|
The DEC DE425 ESIA NIC based on the DC21040-AA is not support at
|
||
|
this time. A future update will include support for it.
|
||
|
|
||
|
The driver includes full support for both BPF and IP Multicast.
|
||
|
If the autosensing of the driver fails, you can use ifconfig(8) to
|
||
|
switch the driver to the correct port.
|
||
|
|
||
|
ifconfig de0 altphys Thinwire/AUI port
|
||
|
ifconfig de0 -altphys 10baseT/UTP port
|
||
|
|
||
|
This driver requires the NCR 53C810 PCI SCSI package to be installed.
|
||
|
This can be obtained from FTP.Uni-Koeln.DE:~ftp/packages/FreeBSD.
|
||
|
|
||
|
[All paths are relative to the top of sys source area, usually
|
||
|
/usr/src/sys.]
|
||
|
|
||
|
The following files need to be moved into their respective
|
||
|
directories:
|
||
|
|
||
|
if_de.c --> i386/pci
|
||
|
dc21040.h --> i386/pci
|
||
|
|
||
|
You will need to apply the following patches:
|
||
|
|
||
|
pat.files.i386 --> i386/conf/files.i386
|
||
|
pat.pci --> i386/pci/pci.c, i386/pci/pci_config.c
|
||
|
|
||
|
After that is done you will need to edit your config file (in
|
||
|
i386/conf) and lines similar to:
|
||
|
|
||
|
controller pci0 at isa? irq 9
|
||
|
device de0
|
||
|
|
||
|
The above assumes the board is configured to use IRQ 9 by your
|
||
|
BIOS. Change the IRQ if need to match your configuration.
|
||
|
|
||
|
Now you are ready to rebuild your kernel, reboot, and see if the
|
||
|
driver can configure your board. When the system boots, you will
|
||
|
hopefully something close to:
|
||
|
|
||
|
on pci0:7 <digital dc21040 ethernet> irq a isa=9 [1] as de0
|
||
|
memory size=0x1000 virtual=0xf25e9000 physical=0xc0001000
|
||
|
de0: enabling Thinwire/AUI port
|
||
|
de0: DC21040 pass 2.3 (TULIP) ethernet address 08:00:2b:e2:1e:09
|
||
|
bpf: de0 attached
|
||
|
|
||
|
in the startup log. If so, the board configured properly and
|
||
|
should be ready to use.
|
||
|
|