/* * Copyright (c) 1993 Herb Peyerl All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions are * met: 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. 2. The name * of the author may not be used to endorse or promote products derived from * this software without specific prior written permission * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO * EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * * From: if_ep.c,v 1.9 1994/01/25 10:46:29 deraadt Exp $ $Id: if_ep.c,v 1.9 * 1994/05/02 22:27:33 ats Exp $ * * October 26, 1994 * * Modified by: Andres Vega Garcia * INRIA - Sophia Antipolis, France * e-mail: avega@sophia.inria.fr * finger: avega@pax.inria.fr * * * What is new: * * 1) We can recognize more than 1 board. * * 2) The problem which used to happen with high trafic is corrected, * (No more need to 'down' and 'up' the interface). * * 3) In the transmission, we use the TX start threshold in a more dynamic * fashion (IMO the throughput is higher this way). * * 4) In the reception, we use the RX early threshold, that parameter is * adapted as the packets arrive (IMO the throughput is higher this way). * * 5) Supports EISA cards. * * NB 0: The 32 bits acces is allowed for the EISA configured cards, thoung I * wasn't able to test the code added. * * NB 1: I added the option EP_LOCAL_STATS, it can be temporary as IMO is just * used while working on this driver and the program that displays this * information (epstat). * * * Some driver statistics can be viewed with the epstat utility. In order to * use this, you have to compile if_ep.c with * * -DEP_LOCAL_STATS * * which can be included in your machine config file (e.g. GENERICAH_EP) * as an option (option EP_LOCAL_STATS). * * * Modifications since FreeBSD 1.1.5.1 Release: * * This explanation concerns the epstart(), epread() and epintr() functions. * * ========================================================================= * epstart() * ========================================================================= * * * Let's see what the idea is: * * * Packet |------------------ LEN ---------------------| * * A * CPU |---------------|----------------------------| * * * Card |----------------------------| * * * * We suppose the Card is able to *write* bytes (send them to the media) * at the speed S_CARD (bytes/s), and that is faster than the speed of the CPU, * S_CPU, to write bytes to the TX FIFO, then, we have to write A bytes to the * FIFO before enableing the transmision in the card. This way both, the card * and the CPU must finish their writing at the same time. * * * Let TX_RATE = S_CPU / S_CARD, where TX_RATE <= 1 * * We can find that: * * (1) A = LEN * (1 - TX_RATE) * * * Let TX_RATE_R be the *very real* value. * * If TX_RATE > TX_RATE_R * We are supposing the CPU is faster than it really is and * certainly the card will *finish* before the CPU, having a * TX Underrun Error, then, in such a case, we have to do: * * TX_RATE -= STEP, where STEP is the step at which we * move TX_RATE * * If TX_RATE < TX_RATE_R * We won't have the TX Underrun Error but it is possible that * we don't use eficiently the TX START THRESH. feature. * We prevent this by doing: * * TX_RATE += STEP every time we have sent succesfuly * (without Underrun) a certain number * of packets. * * Now, to avoid dealing with reals I used a FACTOR, then (1) will be * transformed: * * Let tx_rate = FACTOR * TX_RATE, tx_rate is the parameter * really used. * * A = (LEN * (FACTOR - tx_rate)) / FACTOR * * Actually FACTOR = 64 * * (2) A = (LEN * (64 - tx_rate)) >> 6 * * As I want to have some margin, and * as I have to write a number multiple of 4: * * A = tx_start_threshold = (((LEN * (64 - tx_rate)) >> 6) & ~3) + 16 * * * ========================================================================= * epread() * ========================================================================= * * I mantain an estimation of the RX packet's average length, and an * estimation of the RX latency. * * Every time I receive a complete packet I compute the average packet's * length, rx_avg_pkt: * * DELTA = LEN - rx_avg_pkt, where LEN is this packet's length * * if DELTA > 0 * rx_avg_pkt += AVG_UP * DELTA * else * rx_avg_pkt += AVG_DOWN *DELTA * * * AVG_UP < AVG_DOWN * * In the first case, I'm interested in being conservative about the * average packet'length, because if I let it go up *too fast*, a shorter packet * than expected will probably cause an RX Overrun Error. But if I consider * the next packet will be smaller than it will, I just will have to wait * for the packet to complete reception. * * In the other case, I'm interested in leting the rx_avg_pkt follow * the real packet's lenght closer, as it is important not to think the average * packet is bigger than it realy is. If I don't do that, and the rx_avg_pkt * goes down *too slow*, I'll find myself thinking the packets are big when they * are really small and I'll have probably Rx Overrun Errors. * * Actualy: * * AVG_UP = 1/32 * AVG_DOWN = 1/8 * * * Every time I receive an incomplete packet I recompute the RX latency * (rx_latency). * * I know that if rx_latency = 0, when I go read the bytes from the RX * FIFO, I'll find as many bytes as I programmed in the RX Early Threshold, but * if rx_latency > 0, I'll find more bytes. * * Let CUR_LAT be the RX latency seen by this packet. * * CUR_LAT = LEN - rx_early_threshold, where LEN is the number of * bytes I have just received. * * DELTA = CUR_LAT - rx_latency * * * if DELTA >= 0 * rx_latency += LAT_UP * DELTA * else * rx_latency += LAT_DOWN * DELTA * * * LAT_UP > LAT_DOWN * * In a similar way as for rx average packet's length, I try to be more * conservative in the more critical case. * * In the first case, I have to follow closer the incremets of the RX * latency, because if I don't, I can find myself thinking that we (CPU) are * *enough fast* and wait up to the last minute to go read data to find we have * had RX Overrun Error. * * In the other case I must be more conservative to avoid falling in * the situation I have just described, because if I go down *to fast* I'll * think we are enough fast and we'll wake up later than due. * * Actually: * * LAT_UP = 1/4 * LAT_DOWN = 1/32 * * Finally, I compute the rx_early_threshold for the next packet as: * * rx_early_threshold = rx_avg_pkt - rx_latency * * But, as I want to have a margin and * as I have to write a value multiple of 4. * * * rx_early_threshold = (rx_avg_pkt - rx_latency - 16) & ~3 * * * But if I have to wait for the rest of an incomplete packet * from which I have already received CUR_LEN bytes: * * * rx_early_threshold = (rx_avg_pkt-CUR_LEN - rx_latency - 16) & ~3 * * * ========================================================================= * epintr() * ========================================================================= * * For this function I just tryed to do what is stated in the * Etherlink III Technical Reference. * * It was here where I really solved the problem that used to happen with * high traffic. * * * Andres * avega@pax.inria.fr */ #include "ep.h" #if NEP > 0 #include "bpfilter.h" #include #if defined(__FreeBSD__) #include #include #include #endif #include #include #include #include #include #if defined(__NetBSD__) #include #endif #include #include #include #ifdef INET #include #include #include #include #include #endif #ifdef NS #include #include #endif #if NBPFILTER > 0 #include #include #endif #include #include #include #include static int epprobe __P((struct isa_device *)); static int epattach __P((struct isa_device *)); static int epioctl __P((struct ifnet * ifp, int, caddr_t)); static void epmbuffill __P((caddr_t, int)); static void epmbufempty __P((struct ep_softc *)); void epinit __P((int)); void epintr __P((int)); void epread __P((struct ep_softc *)); void epreset __P((int)); void epstart __P((struct ifnet *)); void epstop __P((int)); void epwatchdog __P((int)); static int send_ID_sequence __P((int)); static int get_eeprom_data __P((int, int)); struct ep_softc ep_softc[NEP]; #define ep_ftst(f) (sc->stat&(f)) #define ep_fset(f) (sc->stat|=(f)) #define ep_frst(f) (sc->stat&=~(f)) struct isa_driver epdriver = { epprobe, epattach, "ep" }; static struct kern_devconf kdc_ep[NEP] = { { 0, 0, 0, /* filled in by dev_attach */ "ep", 0, { MDDT_ISA, 0, "net" }, isa_generic_externalize, 0, 0, ISA_EXTERNALLEN, &kdc_isa0, /* parent */ 0, /* parentdata */ DC_BUSY, /* network interfaces are always ``open'' */ "3Com 3C509 Ethernet adapter" } }; static inline void ep_registerdev(struct isa_device *id) { if(id->id_unit) kdc_ep[id->id_unit] = kdc_ep[0]; kdc_ep[id->id_unit].kdc_unit = id->id_unit; kdc_ep[id->id_unit].kdc_parentdata = id; dev_attach(&kdc_ep[id->id_unit]); } int ep_current_tag = EP_LAST_TAG + 1; int ep_board[EP_MAX_BOARDS + 1]; static int eeprom_rdy(is) struct isa_device *is; { int i; for (i = 0; is_eeprom_busy(IS_BASE) && i < MAX_EEPROMBUSY; i++); if (i >= MAX_EEPROMBUSY) { printf("ep%d: eeprom failed to come ready.\n", is->id_unit); return (0); } return (1); } static int ep_look_for_board_at(is) struct isa_device *is; { int data, i, j, io_base, id_port = EP_ID_PORT; int nisa = 0, neisa = 0; if (ep_current_tag == (EP_LAST_TAG + 1)) { /* Come here just one time */ /* Look for the EISA boards, leave them activated */ for(j = 1; j < 16; j++) { io_base = (j * EP_EISA_START) | EP_EISA_W0; if (inw(io_base + EP_W0_MFG_ID) != MFG_ID) continue; /* we must found 0x1f if the board is EISA configurated */ if ((inw(io_base + EP_W0_ADDRESS_CFG) & 0x1f) != 0x1f) continue; /* Reset and Enable the card */ outb(io_base + EP_W0_CONFIG_CTRL, W0_P4_CMD_RESET_ADAPTER); DELAY(1000); /* we must wait at least 1 ms */ outb(io_base + EP_W0_CONFIG_CTRL, W0_P4_CMD_ENABLE_ADAPTER); /* * Once activated, all the registers are mapped in the range * x000 - x00F, where x is the slot number. */ ep_board[neisa++] = j * EP_EISA_START; } ep_current_tag--; /* Look for the ISA boards. Init and leave them actived */ outb(id_port, 0xc0); /* Global reset */ DELAY(1000); for (i = 0; i < EP_MAX_BOARDS; i++) { outb(id_port, 0); outb(id_port, 0); send_ID_sequence(id_port); data = get_eeprom_data(id_port, EEPROM_MFG_ID); if (data != MFG_ID) break; /* resolve contention using the Ethernet address */ for (j = 0; j < 3; j++) data = get_eeprom_data(id_port, j); ep_board[neisa+nisa++] = (get_eeprom_data(id_port, EEPROM_ADDR_CFG) & 0x1f) * 0x10 + 0x200; outb(id_port, ep_current_tag); /* tags board */ outb(id_port, ACTIVATE_ADAPTER_TO_CONFIG); ep_current_tag--; } ep_board[neisa+nisa] = 0; if (neisa) { printf("%d 3C5x9 board(s) on EISA found at", neisa); for (j = 0; ep_board[j]; j++) if (ep_board[j] >= EP_EISA_START) printf(" 0x%x", ep_board[j]); printf("\n"); } if (nisa) { printf("%d 3C5x9 board(s) on ISA found at", nisa); for (j = 0; ep_board[j]; j++) if (ep_board[j] < EP_EISA_START) printf(" 0x%x", ep_board[j]); printf("\n"); } } for (i = 0; ep_board[i] && ep_board[i] != IS_BASE; i++); if (ep_board[i] == IS_BASE) { if (inw(IS_BASE + EP_W0_EEPROM_COMMAND) & EEPROM_TST_MODE) printf("ep%d: 3c5x9 at 0x%x in test mode. Erase pencil mark!\n", is->id_unit, IS_BASE); return (1); } return (0); } /* * get_e: gets a 16 bits word from the EEPROM. we must have set the window * before */ static int get_e(is, offset) struct isa_device *is; int offset; { if (!eeprom_rdy(is)) return (0xffff); outw(IS_BASE + EP_W0_EEPROM_COMMAND, EEPROM_CMD_RD | offset); if (!eeprom_rdy(is)) return (0xffff); return (inw(IS_BASE + EP_W0_EEPROM_DATA)); } int epprobe(is) struct isa_device *is; { struct ep_softc *sc = &ep_softc[is->id_unit]; u_short k; int i; if (!ep_look_for_board_at(is)) return (0); /* * The iobase was found and MFG_ID was 0x6d50. PROD_ID should be * 0x9[0-f]50 */ GO_WINDOW(0); k = get_e(is, EEPROM_PROD_ID); if ((k & 0xf0ff) != (PROD_ID & 0xf0ff)) { printf("epprobe: ignoring model %04x\n", k); return (0); } k = get_e(is, EEPROM_RESOURCE_CFG); k >>= 12; if (is->id_irq != (1 << ((k == 2) ? 9 : k))) { printf("epprobe: interrupt number %d doesn't match\n",is->id_irq); return (0); } if (BASE >= EP_EISA_START) /* we have an EISA board, we allow 32 bits access */ sc->stat = F_ACCESS_32_BITS; else sc->stat = 0; /* By now, the adapter is already activated */ return (0x10); /* 16 bytes of I/O space used. */ } static char *ep_conn_type[] = {"UTP", "AUI", "???", "BNC"}; static int epattach(is) struct isa_device *is; { struct ep_softc *sc = &ep_softc[is->id_unit]; struct ifnet *ifp = &sc->arpcom.ac_if; u_short i, j, *p; struct ifaddr *ifa; struct sockaddr_dl *sdl; /* BASE = IS_BASE; */ sc->ep_io_addr = is->id_iobase; printf("ep%d: ", is->id_unit); sc->ep_connectors = 0; i = inw(IS_BASE + EP_W0_CONFIG_CTRL); j = inw(IS_BASE + EP_W0_ADDRESS_CFG) >> 14; if (i & IS_AUI) { printf("aui"); sc->ep_connectors |= AUI; } if (i & IS_BNC) { if (sc->ep_connectors) printf("/"); printf("bnc"); sc->ep_connectors |= BNC; } if (i & IS_UTP) { if (sc->ep_connectors) printf("/"); printf("utp"); sc->ep_connectors |= UTP; } if (!(sc->ep_connectors & 7)) printf("no connectors!"); else printf("[*%s*]", ep_conn_type[j]); /* * Read the station address from the eeprom */ p = (u_short *) & sc->arpcom.ac_enaddr; for (i = 0; i < 3; i++) { GO_WINDOW(0); p[i] = htons(get_e(is, i)); GO_WINDOW(2); outw(BASE + EP_W2_ADDR_0 + (i * 2), ntohs(p[i])); } printf(" address %s\n", ether_sprintf(sc->arpcom.ac_enaddr)); ifp->if_unit = is->id_unit; ifp->if_name = "ep"; ifp->if_mtu = ETHERMTU; ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_NOTRAILERS; ifp->if_init = epinit; ifp->if_output = ether_output; ifp->if_start = epstart; ifp->if_ioctl = epioctl; ifp->if_watchdog = epwatchdog; if_attach(ifp); ep_registerdev(is); /* * Fill the hardware address into ifa_addr if we find an AF_LINK entry. * We need to do this so bpf's can get the hardware addr of this card. * netstat likes this too! */ ifa = ifp->if_addrlist; while ((ifa != 0) && (ifa->ifa_addr != 0) && (ifa->ifa_addr->sa_family != AF_LINK)) ifa = ifa->ifa_next; if ((ifa != 0) && (ifa->ifa_addr != 0)) { sdl = (struct sockaddr_dl *) ifa->ifa_addr; sdl->sdl_type = IFT_ETHER; sdl->sdl_alen = ETHER_ADDR_LEN; sdl->sdl_slen = 0; bcopy(sc->arpcom.ac_enaddr, LLADDR(sdl), ETHER_ADDR_LEN); } /* we give some initial parameters */ sc->rx_avg_pkt = 128; /* * NOTE: In all this I multiply everything by 64. * W_s = the speed the CPU is able to write to the TX FIFO. * T_s = the speed the board sends the info to the Ether. * W_s/T_s = 16 (represents 16/64) => W_s = 25 % of T_s. * This will give us for a packet of 1500 bytes * tx_start_thresh=1125 and for a pkt of 64 bytes tx_start_threshold=48. * We prefer to start thinking the CPU is much slower than the Ethernet * transmission. */ sc->tx_rate = TX_INIT_RATE; sc->tx_counter = 0; sc->rx_latency = RX_INIT_LATENCY; sc->rx_early_thresh = RX_INIT_EARLY_THRESH; #ifdef EP_LOCAL_STATS sc->rx_no_first = sc->rx_no_mbuf = sc->rx_bpf_disc = sc->rx_overrunf = sc->rx_overrunl = sc->tx_underrun = 0; #endif ep_fset(F_RX_FIRST); sc->top = sc->mcur = 0; #if NBPFILTER > 0 bpfattach(&sc->bpf, ifp, DLT_EN10MB, sizeof(struct ether_header)); #endif return 1; } /* * The order in here seems important. Otherwise we may not receive * interrupts. ?! */ void epinit(unit) int unit; { register struct ep_softc *sc = &ep_softc[unit]; register struct ifnet *ifp = &sc->arpcom.ac_if; int s, i; if (ifp->if_addrlist == (struct ifaddr *) 0) return; s = splimp(); while (inw(BASE + EP_STATUS) & S_COMMAND_IN_PROGRESS); GO_WINDOW(0); /* Disable the card */ outw(BASE + EP_W0_CONFIG_CTRL, 0); /* Enable the card */ outw(BASE + EP_W0_CONFIG_CTRL, ENABLE_DRQ_IRQ); GO_WINDOW(2); /* Reload the ether_addr. */ for (i = 0; i < 6; i++) outb(BASE + EP_W2_ADDR_0 + i, sc->arpcom.ac_enaddr[i]); outw(BASE + EP_COMMAND, RX_RESET); outw(BASE + EP_COMMAND, TX_RESET); /* Window 1 is operating window */ GO_WINDOW(1); for (i = 0; i < 31; i++) inb(BASE + EP_W1_TX_STATUS); /* get rid of stray intr's */ outw(BASE + EP_COMMAND, ACK_INTR | 0xff); outw(BASE + EP_COMMAND, SET_RD_0_MASK | S_5_INTS); outw(BASE + EP_COMMAND, SET_INTR_MASK | S_5_INTS); outw(BASE + EP_COMMAND, SET_RX_FILTER | FIL_INDIVIDUAL | FIL_GROUP | FIL_BRDCST); /* * you can `ifconfig ep0 (bnc|aui)' to get the following * behaviour: * bnc disable AUI/UTP. enable BNC. * aui disable BNC. enable AUI. if the card has a UTP * connector, that is enabled too. not sure, but it * seems you have to be careful to not plug things * into both AUI & UTP. */ #if defined(__NetBSD__) if (!(ifp->if_flags & IFF_LINK0) && (sc->ep_connectors & BNC)) { #else if (!(ifp->if_flags & IFF_ALTPHYS) && (sc->ep_connectors & BNC)) { #endif outw(BASE + EP_COMMAND, START_TRANSCEIVER); DELAY(1000); } #if defined(__NetBSD__) if ((ifp->if_flags & IFF_LINK0) && (sc->ep_connectors & UTP)) { #else if ((ifp->if_flags & IFF_ALTPHYS) && (sc->ep_connectors & UTP)) { #endif GO_WINDOW(4); outw(BASE + EP_W4_MEDIA_TYPE, ENABLE_UTP); GO_WINDOW(1); } outw(BASE + EP_COMMAND, RX_ENABLE); outw(BASE + EP_COMMAND, TX_ENABLE); ifp->if_flags |= IFF_RUNNING; ifp->if_flags &= ~IFF_OACTIVE; /* just in case */ sc->tx_rate = TX_INIT_RATE; sc->tx_counter = 0; sc->rx_latency = RX_INIT_LATENCY; sc->rx_early_thresh = RX_INIT_EARLY_THRESH; #ifdef EP_LOCAL_STATS sc->rx_no_first = sc->rx_no_mbuf = sc->rx_bpf_disc = sc->rx_overrunf = sc->rx_overrunl = sc->tx_underrun = 0; #endif ep_fset(F_RX_FIRST); ep_frst(F_RX_TRAILER); if (sc->top) { m_freem(sc->top); sc->top = sc->mcur = 0; } outw(BASE + EP_COMMAND, SET_RX_EARLY_THRESH | sc->rx_early_thresh); /* * Store up a bunch of mbuf's for use later. (MAX_MBS). First we free up * any that we had in case we're being called from intr or somewhere * else. */ sc->last_mb = 0; sc->next_mb = 0; epmbuffill((caddr_t) sc, 0); epstart(ifp); splx(s); } static const char padmap[] = {0, 3, 2, 1}; void epstart(ifp) struct ifnet *ifp; { register struct ep_softc *sc = &ep_softc[ifp->if_unit]; register u_int len; register struct mbuf *m; struct mbuf *top; int s, pad; s = splimp(); if (sc->arpcom.ac_if.if_flags & IFF_OACTIVE) { splx(s); return; } startagain: /* Sneak a peek at the next packet */ m = sc->arpcom.ac_if.if_snd.ifq_head; if (m == 0) { splx(s); return; } #if 0 len = m->m_pkthdr.len; #else for (len = 0, top = m; m; m = m->m_next) len += m->m_len; #endif pad = padmap[len & 3]; /* * The 3c509 automatically pads short packets to minimum ethernet length, * but we drop packets that are too large. Perhaps we should truncate * them instead? */ if (len + pad > ETHER_MAX_LEN) { /* packet is obviously too large: toss it */ ++sc->arpcom.ac_if.if_oerrors; IF_DEQUEUE(&sc->arpcom.ac_if.if_snd, m); m_freem(m); goto readcheck; } if (inw(BASE + EP_W1_FREE_TX) < len + pad + 4) { /* no room in FIFO */ outw(BASE + EP_COMMAND, SET_TX_AVAIL_THRESH | (len + pad + 4)); sc->arpcom.ac_if.if_flags |= IFF_OACTIVE; splx(s); return; } IF_DEQUEUE(&sc->arpcom.ac_if.if_snd, m); outw(BASE + EP_W1_TX_PIO_WR_1, len); outw(BASE + EP_W1_TX_PIO_WR_1, 0x0); /* Second dword meaningless */ /* compute the Tx start threshold for this packet */ sc->tx_start_thresh = len = (((len * (64 - sc->tx_rate)) >> 6) & ~3) + 16; outw(BASE + EP_COMMAND, SET_TX_START_THRESH | len); for (top = m; m != 0; m = m->m_next) if(ep_ftst(F_ACCESS_32_BITS)) { outsl(BASE + EP_W1_TX_PIO_WR_1, mtod(m, caddr_t), m->m_len / 4); if (m->m_len & 3) outsb(BASE + EP_W1_TX_PIO_WR_1, mtod(m, caddr_t) + m->m_len / 4, m->m_len & 3); } else { outsw(BASE + EP_W1_TX_PIO_WR_1, mtod(m, caddr_t), m->m_len / 2); if (m->m_len & 1) outb(BASE + EP_W1_TX_PIO_WR_1, *(mtod(m, caddr_t) + m->m_len - 1)); } while (pad--) outb(BASE + EP_W1_TX_PIO_WR_1, 0); /* Padding */ #if NBPFILTER > 0 if (sc->bpf) { bpf_mtap(sc->bpf, top); } #endif sc->arpcom.ac_if.if_opackets++; m_freem(top); /* * Every 1024*4 packets we increment the tx_rate if we haven't had * errors, that in the case it has abnormaly goten too low */ if (!(++sc->tx_counter & (1024 * 4 - 1)) && sc->tx_rate < TX_INIT_MAX_RATE) sc->tx_rate++; /* * Is another packet coming in? We don't want to overflow the tiny RX * fifo. */ readcheck: if (inw(BASE + EP_W1_RX_STATUS) & RX_BYTES_MASK) { /* * we check if we have packets left, in that case we prepare to come * back later */ if (sc->arpcom.ac_if.if_snd.ifq_head) { outw(BASE + EP_COMMAND, SET_TX_AVAIL_THRESH | sc->tx_start_thresh); } splx(s); return; } goto startagain; } void epintr(unit) int unit; { int i; register int status; register struct ep_softc *sc = &ep_softc[unit]; struct ifnet *ifp = &sc->arpcom.ac_if; struct mbuf *m; outw(BASE + EP_COMMAND, SET_INTR_MASK); /* disable all Ints */ outw(BASE + EP_COMMAND, C_INTR_LATCH); /* ACK int Latch */ while ((status = inw(BASE + EP_STATUS)) & S_5_INTS) { if (status & (S_RX_COMPLETE | S_RX_EARLY)) { /* we just need ACK for RX_EARLY */ if (status & S_RX_EARLY) outw(BASE + EP_COMMAND, C_RX_EARLY); epread(sc); continue; } if (status & S_TX_AVAIL) { /* we need ACK */ outw(BASE + EP_COMMAND, C_TX_AVAIL); sc->arpcom.ac_if.if_flags &= ~IFF_OACTIVE; epstart(&sc->arpcom.ac_if); } if (status & S_CARD_FAILURE) { #ifdef EP_LOCAL_STATS printf("\nep%d:\n\tStatus: %x\n", unit, status); GO_WINDOW(4); printf("\tFIFO Diagnostic: %x\n", inw(BASE + EP_W4_FIFO_DIAG)); printf("\tStat: %x\n", sc->stat); printf("\tIpackets=%d, Opackets=%d\n", sc->arpcom.ac_if.if_ipackets, sc->arpcom.ac_if.if_opackets); printf("\tNOF=%d, NOMB=%d, BPFD=%d, RXOF=%d, RXOL=%d, TXU=%d\n", sc->rx_no_first, sc->rx_no_mbuf, sc->rx_bpf_disc, sc->rx_overrunf, sc->rx_overrunl, sc->tx_underrun); #else printf("ep%d: Status: %x\n", unit, status); #endif epinit(unit); return; } if (status & S_TX_COMPLETE) { /* we need ACK. we do it at the end */ /* * We need to read TX_STATUS until we get a 0 status in order to * turn off the interrupt flag. */ while ((status = inb(BASE + EP_W1_TX_STATUS)) & TXS_COMPLETE) { if (status & TXS_SUCCES_INTR_REQ); else if (status & (TXS_UNDERRUN | TXS_JABBER | TXS_MAX_COLLISION)) { outw(BASE + EP_COMMAND, TX_RESET); if (status & TXS_UNDERRUN) { if (sc->tx_rate > 1) { sc->tx_rate--; /* Actually in steps of 1/64 */ sc->tx_counter = 0; /* We reset it */ } #ifdef EP_LOCAL_STATS sc->tx_underrun++; #endif } else { if (status & TXS_JABBER); else /* TXS_MAX_COLLISION - we shouldn't get here */ ++sc->arpcom.ac_if.if_collisions; } ++sc->arpcom.ac_if.if_oerrors; outw(BASE + EP_COMMAND, TX_ENABLE); /* * To have a tx_avail_int but giving the chance to the * Reception */ if (sc->arpcom.ac_if.if_snd.ifq_head) { outw(BASE + EP_COMMAND, SET_TX_AVAIL_THRESH | 8); } } outb(BASE + EP_W1_TX_STATUS, 0x0); /* pops up the next * status */ } /* while */ } /* end TX_COMPLETE */ } /* re-enable ints */ outw(BASE + EP_COMMAND, SET_INTR_MASK | S_5_INTS); } void epread(sc) register struct ep_softc *sc; { struct ether_header *eh; struct mbuf *top, *mcur, *m; int lenthisone; short rx_fifo2, status; register short delta; register short rx_fifo; status = inw(BASE + EP_W1_RX_STATUS); read_again: if (status & ERR_RX) { ++sc->arpcom.ac_if.if_ierrors; if (status & ERR_RX_OVERRUN) { /* * we can think the rx latency is actually greather than we * expect */ #ifdef EP_LOCAL_STATS if (ep_ftst(F_RX_FIRST)) sc->rx_overrunf++; else sc->rx_overrunl++; #endif if (sc->rx_latency < ETHERMTU) sc->rx_latency += 16; } goto out; } rx_fifo = rx_fifo2 = status & RX_BYTES_MASK; if (ep_ftst(F_RX_FIRST)) { if (m = sc->mb[sc->next_mb]) { sc->mb[sc->next_mb] = 0; sc->next_mb = (sc->next_mb + 1) % MAX_MBS; m->m_data = m->m_pktdat; m->m_flags = M_PKTHDR; } else { MGETHDR(m, M_DONTWAIT, MT_DATA); if (!m) goto out; } sc->top = sc->mcur = top = m; #define EROUND ((sizeof(struct ether_header) + 3) & ~3) #define EOFF (EROUND - sizeof(struct ether_header)) top->m_data += EOFF; /* Read what should be the header. */ insw(BASE + EP_W1_RX_PIO_RD_1, mtod(top, caddr_t), sizeof(struct ether_header) / 2); top->m_len = sizeof(struct ether_header); rx_fifo -= sizeof(struct ether_header); sc->cur_len = rx_fifo2; } else { /* come here if we didn't have a complete packet last time */ top = sc->top; m = sc->mcur; sc->cur_len += rx_fifo2; if (ep_ftst(F_RX_TRAILER)) /* We don't read the trailer */ rx_fifo -= sizeof(struct ether_header); } /* Reads what is left in the RX FIFO */ while (rx_fifo > 0) { lenthisone = min(rx_fifo, M_TRAILINGSPACE(m)); if (lenthisone == 0) { /* no room in this one */ mcur = m; if (m = sc->mb[sc->next_mb]) { sc->mb[sc->next_mb] = 0; sc->next_mb = (sc->next_mb + 1) % MAX_MBS; } else { MGET(m, M_DONTWAIT, MT_DATA); if (!m) goto out; } if (rx_fifo >= MINCLSIZE) MCLGET(m, M_DONTWAIT); m->m_len = 0; mcur->m_next = m; lenthisone = min(rx_fifo, M_TRAILINGSPACE(m)); } if (ep_ftst(F_ACCESS_32_BITS)) { /* default for EISA configured cards*/ insl(BASE + EP_W1_RX_PIO_RD_1, mtod(m, caddr_t) + m->m_len, lenthisone / 4); m->m_len += (lenthisone & ~3); if (lenthisone & 3) insb(BASE + EP_W1_RX_PIO_RD_1, mtod(m, caddr_t) + m->m_len, lenthisone & 3); m->m_len += (lenthisone & 3); } else { insw(BASE + EP_W1_RX_PIO_RD_1, mtod(m, caddr_t) + m->m_len, lenthisone / 2); m->m_len += lenthisone; if (lenthisone & 1) *(mtod(m, caddr_t) + m->m_len - 1) = inb(BASE + EP_W1_RX_PIO_RD_1); } rx_fifo -= lenthisone; } if (ep_ftst(F_RX_TRAILER)) {/* reads the trailer */ if (m = sc->mb[sc->next_mb]) { sc->mb[sc->next_mb] = 0; sc->next_mb = (sc->next_mb + 1) % MAX_MBS; m->m_data = m->m_pktdat; m->m_flags = M_PKTHDR; } else { MGETHDR(m, M_DONTWAIT, MT_DATA); if (!m) goto out; } insw(BASE + EP_W1_RX_PIO_RD_1, mtod(m, caddr_t), sizeof(struct ether_header)); m->m_len = sizeof(struct ether_header); m->m_next = top; sc->top = top = m; /* XXX Accomodate for type and len from beginning of trailer */ sc->cur_len -= (2 * sizeof(u_short)); ep_frst(F_RX_TRAILER); goto all_pkt; } if (status & ERR_RX_INCOMPLETE) { /* we haven't received the complete * packet */ sc->mcur = m; #ifdef EP_LOCAL_STATS sc->rx_no_first++; /* to know how often we come here */ #endif /* * Re-compute rx_latency, the factor used is 1/4 to go up and 1/32 to * go down */ delta = rx_fifo2 - sc->rx_early_thresh; /* last latency seen LLS */ delta -= sc->rx_latency;/* LLS - estimated_latency */ if (delta >= 0) sc->rx_latency += (delta / 4); else sc->rx_latency += (delta / 32); ep_frst(F_RX_FIRST); if (!((status = inw(BASE + EP_W1_RX_STATUS)) & ERR_RX_INCOMPLETE)) { /* we see if by now, the packet has completly arrived */ goto read_again; } /* compute rx_early_threshold */ delta = (sc->rx_avg_pkt - sc->cur_len - sc->rx_latency - 16) & ~3; if (delta < MIN_RX_EARLY_THRESHL) delta = MIN_RX_EARLY_THRESHL; outw(BASE + EP_COMMAND, SET_RX_EARLY_THRESH | (sc->rx_early_thresh = delta)); return; } all_pkt: outw(BASE + EP_COMMAND, RX_DISCARD_TOP_PACK); /* * recompute average packet's length, the factor used is 1/8 to go down * and 1/32 to go up */ delta = sc->cur_len - sc->rx_avg_pkt; if (delta > 0) sc->rx_avg_pkt += (delta / 32); else sc->rx_avg_pkt += (delta / 8); delta = (sc->rx_avg_pkt - sc->rx_latency - 16) & ~3; if (delta < MIN_RX_EARLY_THRESHF) delta = MIN_RX_EARLY_THRESHF; sc->rx_early_thresh = delta; ++sc->arpcom.ac_if.if_ipackets; ep_fset(F_RX_FIRST); ep_frst(F_RX_TRAILER); top->m_pkthdr.rcvif = &sc->arpcom.ac_if; top->m_pkthdr.len = sc->cur_len; #if NBPFILTER > 0 if (sc->bpf) { bpf_mtap(sc->bpf, top); /* * Note that the interface cannot be in promiscuous mode if there are * no BPF listeners. And if we are in promiscuous mode, we have to * check if this packet is really ours. */ eh = mtod(top, struct ether_header *); if ((sc->arpcom.ac_if.if_flags & IFF_PROMISC) && (eh->ether_dhost[0] & 1) == 0 && bcmp(eh->ether_dhost, sc->arpcom.ac_enaddr, sizeof(eh->ether_dhost)) != 0 && bcmp(eh->ether_dhost, etherbroadcastaddr, sizeof(eh->ether_dhost)) != 0) { if (sc->top) { m_freem(sc->top); sc->top = 0; } ep_fset(F_RX_FIRST); ep_frst(F_RX_TRAILER); #ifdef EP_LOCAL_STATS sc->rx_bpf_disc++; #endif while (inw(BASE + EP_STATUS) & S_COMMAND_IN_PROGRESS); outw(BASE + EP_COMMAND, SET_RX_EARLY_THRESH | delta); return; } } #endif eh = mtod(top, struct ether_header *); m_adj(top, sizeof(struct ether_header)); ether_input(&sc->arpcom.ac_if, eh, top); if (!sc->mb[sc->next_mb]) epmbuffill((caddr_t) sc, 0); sc->top = 0; while (inw(BASE + EP_STATUS) & S_COMMAND_IN_PROGRESS); outw(BASE + EP_COMMAND, SET_RX_EARLY_THRESH | delta); return; out: outw(BASE + EP_COMMAND, RX_DISCARD_TOP_PACK); if (sc->top) { m_freem(sc->top); sc->top = 0; #ifdef EP_LOCAL_STATS sc->rx_no_mbuf++; #endif } delta = (sc->rx_avg_pkt - sc->rx_latency - 16) & ~3; if (delta < MIN_RX_EARLY_THRESHF) delta = MIN_RX_EARLY_THRESHF; ep_fset(F_RX_FIRST); ep_frst(F_RX_TRAILER); while (inw(BASE + EP_STATUS) & S_COMMAND_IN_PROGRESS); outw(BASE + EP_COMMAND, SET_RX_EARLY_THRESH | (sc->rx_early_thresh = delta)); } /* * Look familiar? */ static int epioctl(ifp, cmd, data) register struct ifnet *ifp; int cmd; caddr_t data; { register struct ifaddr *ifa = (struct ifaddr *) data; struct ep_softc *sc = &ep_softc[ifp->if_unit]; struct ifreq *ifr = (struct ifreq *) data; int s, error = 0; switch (cmd) { case SIOCSIFADDR: ifp->if_flags |= IFF_UP; switch (ifa->ifa_addr->sa_family) { #ifdef INET case AF_INET: epinit(ifp->if_unit); /* before arpwhohas */ ((struct arpcom *) ifp)->ac_ipaddr = IA_SIN(ifa)->sin_addr; arpwhohas((struct arpcom *) ifp, &IA_SIN(ifa)->sin_addr); break; #endif #ifdef NS case AF_NS: { register struct ns_addr *ina = &(IA_SNS(ifa)->sns_addr); if (ns_nullhost(*ina)) ina->x_host = *(union ns_host *) (sc->arpcom.ac_enaddr); else { ifp->if_flags &= ~IFF_RUNNING; bcopy((caddr_t) ina->x_host.c_host, (caddr_t) sc->arpcom.ac_enaddr, sizeof(sc->arpcom.ac_enaddr)); } epinit(ifp->if_unit); break; } #endif default: epinit(ifp->if_unit); break; } break; case SIOCSIFFLAGS: if ((ifp->if_flags & IFF_UP) == 0 && ifp->if_flags & IFF_RUNNING) { ifp->if_flags &= ~IFF_RUNNING; epstop(ifp->if_unit); epmbufempty(sc); break; } if (ifp->if_flags & IFF_UP && (ifp->if_flags & IFF_RUNNING) == 0) epinit(ifp->if_unit); break; #ifdef notdef case SIOCGHWADDR: bcopy((caddr_t) sc->sc_addr, (caddr_t) & ifr->ifr_data, sizeof(sc->sc_addr)); break; #endif case SIOCSIFMTU: /* * Set the interface MTU. */ if (ifr->ifr_mtu > ETHERMTU) { error = EINVAL; } else { ifp->if_mtu = ifr->ifr_mtu; } break; default: error = EINVAL; } return (error); } void epreset(unit) int unit; { int s = splimp(); epstop(unit); epinit(unit); splx(s); } void epwatchdog(unit) int unit; { struct ep_softc *sc = &ep_softc[unit]; log(LOG_ERR, "ep%d: watchdog\n", unit); ++sc->arpcom.ac_if.if_oerrors; epreset(unit); } void epstop(unit) int unit; { struct ep_softc *sc = &ep_softc[unit]; outw(BASE + EP_COMMAND, RX_DISABLE); outw(BASE + EP_COMMAND, RX_DISCARD_TOP_PACK); while (inw(BASE + EP_STATUS) & S_COMMAND_IN_PROGRESS); outw(BASE + EP_COMMAND, TX_DISABLE); outw(BASE + EP_COMMAND, STOP_TRANSCEIVER); outw(BASE + EP_COMMAND, RX_RESET); outw(BASE + EP_COMMAND, TX_RESET); outw(BASE + EP_COMMAND, C_INTR_LATCH); outw(BASE + EP_COMMAND, SET_RD_0_MASK); outw(BASE + EP_COMMAND, SET_INTR_MASK); outw(BASE + EP_COMMAND, SET_RX_FILTER); } static int send_ID_sequence(port) int port; { int cx, al; for (al = 0xff, cx = 0; cx < 255; cx++) { outb(port, al); al <<= 1; if (al & 0x100) al ^= 0xcf; } return (1); } /* * We get eeprom data from the id_port given an offset into the eeprom. * Basically; after the ID_sequence is sent to all of the cards; they enter * the ID_CMD state where they will accept command requests. 0x80-0xbf loads * the eeprom data. We then read the port 16 times and with every read; the * cards check for contention (ie: if one card writes a 0 bit and another * writes a 1 bit then the host sees a 0. At the end of the cycle; each card * compares the data on the bus; if there is a difference then that card goes * into ID_WAIT state again). In the meantime; one bit of data is returned in * the AX register which is conveniently returned to us by inb(). Hence; we * read 16 times getting one bit of data with each read. */ static int get_eeprom_data(id_port, offset) int id_port; int offset; { int i, data = 0; outb(id_port, 0x80 + offset); DELAY(1000); for (i = 0; i < 16; i++) data = (data << 1) | (inw(id_port) & 1); return (data); } /* * We suppose this is always called inside a splimp(){...}splx() region */ static void epmbuffill(sp, dummy_arg) caddr_t sp; int dummy_arg; { struct ep_softc *sc = (struct ep_softc *) sp; int i; i = sc->last_mb; do { if (sc->mb[i] == NULL) MGET(sc->mb[i], M_DONTWAIT, MT_DATA); if (sc->mb[i] == NULL) break; i = (i + 1) % MAX_MBS; } while (i != sc->next_mb); sc->last_mb = i; } static void epmbufempty(sc) struct ep_softc *sc; { int s, i; s = splimp(); for (i = 0; i < MAX_MBS; i++) { if (sc->mb[i]) { m_freem(sc->mb[i]); sc->mb[i] = NULL; } } sc->last_mb = sc->next_mb = 0; splx(s); } #endif /* NEP > 0 */