mirror of
https://github.com/freebsd/freebsd-src.git
synced 2024-12-03 08:22:44 +00:00
57 lines
3.1 KiB
Plaintext
57 lines
3.1 KiB
Plaintext
You can do network installations over 3 types of communications links:
|
|
|
|
Serial port: SLIP / PPP
|
|
Parallel port: PLIP (laplink cable)
|
|
Ethernet: A standard Ethernet controller (includes some
|
|
PCMCIA networking cards).
|
|
|
|
SLIP support is rather primitive and limited primarily to directly
|
|
connected links, such as a serial cable running between a laptop
|
|
computer and another PC. The link must be hard-wired as the SLIP
|
|
installation doesn't currently offer a dialing capability (that
|
|
facility is offered by the PPP utility, which should be used in
|
|
preference to SLIP whenever possible). When you choose the SLIP
|
|
option, you'll be given the option of later editing the slattach
|
|
command before it's run on the serial line. It is expected that
|
|
you'll run slattach (or some equivalent command) on the other end of
|
|
the link at that time and bring up the line. FreeBSD will then
|
|
install itself at serial speeds of up to 115.2K/baud (the recommended
|
|
speed for a hardwired cable).
|
|
|
|
If you're using a modem then PPP is almost certainly your only choice.
|
|
Make sure that you have your service provider's information handy as
|
|
you'll need to know it fairly early in the installation process. You
|
|
will need to know, at the minimum, your service provider's IP address
|
|
and possibly your own (though you can also leave it blank and allow
|
|
PPP to negotiate it with your ISP if your ISP supports such dynamic
|
|
negotiation). You will also need to know how to use the various "AT
|
|
commands" to dial the ISP with your particular brand of modem as the
|
|
PPP dialer provides only a very simple terminal emulator and has no
|
|
"modem capabilities database".
|
|
|
|
If a hard-wired connection to another FreeBSD (2.0R or later) machine
|
|
is available, you might also consider installing over a "laplink"
|
|
parallel port cable. The data rate over the parallel port is much
|
|
higher than what is typically possible over a serial line, and speeds
|
|
of up to 50KB/sec are not uncommon.
|
|
|
|
Finally, for the fastest possible network installation, an Ethernet
|
|
adaptor is always a good choice! FreeBSD supports most common PC
|
|
Ethernet cards, a table of which is provided in the FreeBSD Hardware
|
|
Guide (see the Documentation menu on the boot floppy). If you are
|
|
using one of the supported PCMCIA Ethernet cards, also be sure that
|
|
it's plugged in _before_ the laptop is powered on! FreeBSD does not,
|
|
unfortunately, currently support "hot insertion" of PCMCIA cards.
|
|
|
|
You will also need to know your IP address on the network, the
|
|
"netmask" value for your address class, and the name of your machine.
|
|
Your system administrator can tell you which values to use for your
|
|
particular network setup. If you will be referring to other hosts by
|
|
name rather than IP address, you'll also need a name server and
|
|
possibly the address of a gateway (if you're using PPP, it's your
|
|
provider's IP address) to use in talking to it. If you do not know
|
|
the answers to all or most of these questions then you should really
|
|
probably talk to your system administrator _first_ before trying this
|
|
type of installation! Choosing the wrong IP address on a busy network
|
|
will NOT make you popular with your systems administrator! :-)
|