happen when the vm system maps past the end of an object or tries
to map a zero length object, the pmap layer misses the fact that
offsets wrap into negative numbers and we get stuck.
Found by: Joost Pol aka Nohican <nohican@marcella.niets.org>
Submitted by: tegge
When the printer is turned off the pipe write will cause and error,
which causes lpd to close the device and reopen it to clear the error.
After a short while the device will disappear from the bus but lpd will
have opened the ulpt0 port by then. ulpt_status will check for status
without checking the sc->dying flag and panic the kernel when the device
finally disappears from the bus.
Submitted by: Ian Dowse <iedowse@maths.tcd.ie>
also
- sync with netbsd
- fix a bug that miscalculates tx cell counts when the pointer size isn't 4
tested both ENI and Adaptec cards on both i386 and alpha.
function declared in kern_ktr.c. The only inline checks left are the
checks that compare KTR_COMPILE with the supplied mask and thus should
be optimized away into either nothing or a direct call to ktr_tracepoint().
- Move several KTR-related options to opt_ktr.h now that they are only
needed by kern_ktr.c and not by ktr.h.
- Add in the ktr_verbose functionality if KTR_EXTEND is turned on. If the
global variable 'ktr_verbose' is non-zero, then KTR messages will be
dumped to the console. This variable can be set by either kernel code
or via the 'debug.ktr_verbose' sysctl. It defaults to off unless the
KTR_VERBOSE kernel option is specified in which case it defaults to on.
This can be useful when the machine locks up spinning in a loop with
interrupts disabled as you might be able to see what it is doing when it
locks up.
Requested by: phk
interface. In addition to using newbus, it also uses bus_space rather
than inb/outb to make it MI. The grody static softc allocation stuff
has been removed as well.
When restarting the sequencer, ensure that the SCBCNT register
is 0. A non-zero count will prevent the setting of the CCSCBDIR
bit in any future dma operations. The only time CCSCBCNT would
be non-zero is if we happened to halt the dma during a reset,
but even that should never happen. Better safe than sorry.
When a command completes before the target responds to an
ATN for a recovery command, we now notify the kernel so that
any recovery operation requeued in the qinfifo can be removed
safely. In the past, we did this in ahc_done(), but ahc_done()
may be called without the card paused. This also avoids a
recursive call to ahc_search_qinifo() which could have occurred if
ahc_search_qinififo() happened to be the routine to complete
a recovery action.
Fix 8bit math used for adjusting the qinfifo. The index must
be wrapped properly within the 256 entry array. We rely on the
fact that qinfifonext is a uint8_t in most cases to handle
this wrap, but we missed a few spots where the resultant
calculation was promoted to an int.
Change the way that we deal with aborting the first or second
entry from the qinfifo. We now swap the first entry in the
qinfifo with the "next queued scb" to force the sequencer
to see an abort collision if we ever touch the qinififo while
the sequencer is mid SCB dma.
aic7xxx.reg:
Add new MKMSG_FAILED sequencer interrupt. This displaced
the BOGUS_TAG interrupt used in some previous sequencer code
debugging.
aic7xxx.seq:
Increment our position in the qinfifo only once the dma
is complete and we have verified that the queue has not
been changed during our DMA. This simplifies code in the
kernel.
Protect against "instruction creep" when issuing a pausing
sequencer interrupt. On at least the 7890/91/96/97, the
sequencer will coast after issuing the interrupt for up
to two instructions. In the past we delt with this by
using carefully placed nops. Now we call a routine to
issue the interrupt followed by a nop and a ret.
Tell the kernel should an SCB complete with the MK_MESSAGE
flag still set. This means the target ignored our ATN request.
Clear the channel twice as we exit the data phase. On the
aic7890/91, the S/G preload logic may require the second
clearing to get the last S/G out of the FIFO.
aic7xxx_freebsd.c:
Don't bother searching the qinfifo for a doubly queued
recovery scb in ahc_done. This case is handled by the
core driver now.
Free the path used to issue async callbacks after the callback
is complete.
aic7xxx_inline.h:
Split the SCB queue routine into a routine that swaps
the SCB with the "next queued SCB" and a routine that
calls the swapping routine and notifies the card of
the new SCB. The swapping routine is now also used by
ahc_search_qinfifo.
program to read any file which is a valid crontab file.
The fix is based on that used in NetBSD and OpenBSD - we keep the
file open while the user is editing it. This means that files must
be edited in place. Cron attempts to warn you if your editor does
not do this. The fact that the file must be edited in place is also
noted in the man page.
This patch has been confirmed to work by atleast one person on
-security and has been tested locally.
Obtained from: OpenBSD
