m0zah/GB3TX/GB3TX.ino

#include "config.h"
#include "repeater.h"

void setup() {
  pinMode(3, OUTPUT);
  pinMode(8, OUTPUT);
  pinMode(9, OUTPUT);
  pinMode(7, INPUT_PULLUP);
  pinMode(6, INPUT_PULLUP);
  pinMode(PIP_ATT, OUTPUT);
}

void loop() {
  repeater rpt;
  repeater* myrpt;
  myrpt = &rpt;
  myrpt->callsign = ID;
  myrpt->params.cw_pitch = CW_PITCH;
  myrpt->serial.enable = SERIAL;
  myrpt->serial.speed = 115200;
  if (myrpt->serial.enable)
    Serial.begin(myrpt->serial.speed);

  /* Setup params */
  myrpt->params.cw_speed = 1200 / CW_SPEED;
  myrpt->params.close_down = CLOSEDOWN;
  myrpt->params.pip_length = RFPIPLEN;
  myrpt->params.pip_pitch = RFPIP;
  myrpt->params.pip_gw_pitch = RFPIP;
  myrpt->params.pip_gw_length = GWPIPLEN;
  myrpt->params.courtesy = COURTESY;
  myrpt->params.pip_letter = PIP_LETTER;
  myrpt->params.pip_gw_letter = PIP_GW_LETTER;
  myrpt->params.start_up = START;

  delay(1000);
  myrpt->transmitter.tx = true;
  sendID(myrpt);
  myrpt->state = SLEEP;
 
  unsigned long ht = millis();
  unsigned long tot = ht;
  unsigned long kc;
  myrpt->id_time = 0;
  serial_writer(&myrpt->serial, "READY");
  digitalWrite(PIP_ATT, LOW);
  myrpt->stats.gw_time = 0;
  myrpt->stats.tx_time = 0;
  myrpt->stats.rx_time = 0;
  while (1) {
    serial_command(&myrpt->serial, myrpt);
    rx(myrpt);

    if (busy(myrpt) && myrpt->state < KEYCHUNK) {
      myrpt->state = KEYCHUNK;
      serial_writer(&myrpt->serial, "KEYCHUNK");
      kc = millis();
    }

    if (myrpt->state == KEYCHUNK && millis() - kc > KEYCHUNK_TIME) {
      if (!myrpt->receiver.rx) {
        myrpt->state = TT;
        serial_writer(&myrpt->serial, "RX: RF");
      } else {
        myrpt->state = GW;
        serial_writer(&myrpt->serial, "RX: GATEWAY");
        myrpt->timer.gw_start = millis();
      }
      tot = millis();
      if (myrpt->params.start_up)
        sendID(myrpt);
    }

    if ((myrpt->receiver.rx && myrpt->gateway.receiver.rx) && myrpt->state == KEYCHUNK) {
      serial_writer(&myrpt->serial, "SHORT SIGNAL");
      myrpt->state = IDLE;
    }

    if ((myrpt->receiver.rx && myrpt->gateway.receiver.rx) && myrpt->state > HANG) {
      serial_writer(&myrpt->serial, "HANG");
      if (myrpt->state == GW)
        myrpt->stats.gw_time += millis() - myrpt->timer.gw_start;
      delay(500);
      myrpt->last = myrpt->state;
      myrpt->state = HANG;
      ht = millis();
      myrpt->tail = ht;
      if (ht - tot < PIP_KEYCHUNK || busy(myrpt))
        continue;
      courtesyTone(myrpt);
    }

    if (myrpt->state == HANG && TAILPIPS) {
      if (millis() - myrpt->tail >= TAIL_PIP_DELAY && !busy(myrpt)) {
        myrpt->tail = millis();
        tone(PIP, TAILPIP_PITCH, myrpt->params.pip_length);
      }
    }

    if (!myrpt->receiver.rx && myrpt->state == HANG) {
      serial_writer(&myrpt->serial, "RX: RF");
      myrpt->state = TT;
      tot = millis();
    }

    if (!myrpt->gateway.receiver.rx && myrpt->state == HANG) {
      serial_writer(&myrpt->serial, "RX: GATEWAY");
      myrpt->state = GW;
      tot = millis();
    }

    if (millis() - tot >= TIMEOUT && (myrpt->state == TT || myrpt->state == GW)) {
      serial_writer(&myrpt->serial, "REPEATER: TIMEOUT");
      myrpt->state = TIMEOUT;
      tone(PIP, 440, 1000);
      delay(1000);
    }

    if (myrpt->state == HANG && millis() - ht > HANGTIME) {
      if (myrpt->params.close_down) {
        serial_writer(&myrpt->serial, "REPEATER: CLOSEDOWN ID");
        myrpt->state = SLEEP;
        sendID(myrpt);
        continue;
      }
      serial_writer(&myrpt->serial, "REPEATER: IDLE");
      myrpt->state = IDLE;
    }

    if (myrpt->state == TIMEOUT) {
      myrpt->state = IDLE;
      tx(myrpt);
      while (1) {
        rx(myrpt);
        if (myrpt->receiver.rx && myrpt->gateway.receiver.rx)
          break;
      }
      serial_writer(&myrpt->serial, "REPEATER: TIMEOUT RESET");
    }

    if (myrpt->state > SLEEP && millis() - myrpt->id_time >= (IDTIME - 60000)) {
      
      /* Check if the repeater is in use 
       * wait the full ID time 
       */

      if (myrpt->state > IDLE && millis() - myrpt->id_time < IDTIME) {
        continue;
      }

      /* Repeater is IDLE, bring the transmitter up */
      if (!myrpt->transmitter.tx) {
        myrpt->state = HANG;
        tx(myrpt);
        myrpt->state = SLEEP;
      }
      serial_writer(&myrpt->serial, "REPEATER: ID");
      delay(250);
      sendID(myrpt);
    }

    tx(myrpt);
  }

}